- Leaving a door or drawer open causes the light terminator to reach a high temperature, which disables the illumination in that particular region of the room exclusively. The machine will continue to operate (compressor and evaporator fan will both run). Close the door and don’t let anyone in or out for 45 minutes. When the terminator has cooled down, the illumination will be turned back on.
Why did my light go out in my Sub-Zero refrigerator?
If the temperatures on the display are dim, it is possible that the equipment is in Sabbath Mode. Instructions on how to exit Sabbath Mode may be found in the Sabbath Mode Information section. If the door is left open for an extended period of time, the light terminator function can be activated, which will turn out the lights. For information on how to reset light terminators, see Light Terminators.
How do you reset a Sub-Zero refrigerator?
To reset a Sub-Zero product, follow these steps:
- Turn the machine off by pressing the power button on the control panel. If your machine has a dial control, set it to zero (0) or turn it completely off. Turn off the house circuit breaker that serves the device for 30 seconds and then turn it back on. Re-evaluate the operation of the unit.
Where is the light button on Sub-Zero refrigerator?
When using an over-and-under refrigerator, the freezer light, the fan, and the ice maker switch are located on the rear wall of the unit, below the ice bin, or under the ice maker, depending on the model.
What is a light Terminator?
Light terminators are a safety device that helps to keep a unit’s temperature from rising too high. When lights are kept on for extended periods of time, they may grow extremely hot. When the light terminator is activated, the control panel is deactivated in the majority of models that have this function and will not respond.
What happens when fridge light goes out?
A total power loss to the house will result in the failure of the lightbulb in the refrigerator, as well as the failure of every other light fixture and appliance in your residence. If this occurs, try to keep the refrigerator door closed as much as possible to safeguard the food within until the electricity is re-established.
How do I change the bulb in my subzero 632?
Remove the old bulb from the top of the drawer compartment by twisting it in the opposite direction of the clock. Replace the old appliance bulb with a new 25-watt appliance bulb and twist it clockwise to secure it in place. Pushing the light diffuser down into its slots will return it to its original position. Return the shelf and/or drawer to their original positions.
How do you remove a subzero diffuser?
Removal of the Light Diffuser
- The diffuser may be removed by lifting the center of each of the front tabs and pushing the diffuser toward the rear wall. Take a look at the image below. There are two tabs, one on each side of the screen, one on each side of the screen. Make a little downward bend on the front edge of the diffuser. Remove the diffuser from the appliance by pulling it forward.
Why did my Sub-Zero stopped working?
Check to verify that the power cable is firmly connected to the unit’s electrical socket. Unplug the unit and re-plug it into the outlet. Check to see if the electrical outlet is operational. Test with a different appliance, extension cable, or phone charger to see if the problem persists.
How do I reset my Sub-Zero air filter?
To pick the air filter settings, press and hold the flowing air icon in the middle of the display for 5 seconds to bring up the menu. If a filter is available to replace the existing filter, select Reset Filter from the drop-down menu. To reset the filter life, select Yes from the drop-down menu.
What does the wrench symbol mean on a Sub Zero refrigerator?
Service Icon Appearance: When the VS24 Vacuum Seal Drawer does not get a satisfactory seal, the service icon will show. Using a wet cloth, wipe the lid gasket clean. If the service icon does not disappear or does not disappear within a short period of time, service is required to correctly diagnose and fix the product.
What does EC mean on a sub zero?
Cause: EC 05: The refrigerator’s temperature readings are irregular on a regular basis. EC 06: The refrigerator evaporator thermistor displayed an open or shorted state for more than 10 seconds or displayed unpredictable temperatures frequently.
How do you reset the filter on a Sub Zero ice maker?
Make a quarter turn counterclockwise to release the cartridge from the printer’s cartridge holder. Make use of a jar opener to assist you get a stronger grip on a difficult-to-remove filter. Installing the new water filter requires a reversal of the procedure. Press and hold the CLEAN key for 6 seconds to reset the counter and light once you’ve finished replacing the filter.