- The ideal thickness of the bridge is 1/8 inch. To get a rough idea of how thick the ice bridge should be, I’ve used (or once used) a 3/16′′ Allen wrench as a thickness measurement tool to establish the ice bridge thickness. Insert that little wrench between the sensor and the evaporator plate, and then adjust the sensor to 3/16 inch.
How do you make ice thicker on a Scotsman ice maker?
With a model that has an adjustment button, you can simply open the machine and push either a + or – sign to change the thickness of your ice. Pages 9 and 10 of the Scotsman handbook include the necessary instructions to do this task.
How do you adjust a Scotsman ice maker?
If necessary, make the following adjustments to ensure that the right size is achieved: Locate the cube size control knob, which is located on the front of the control panel. Turn this knob one eighth of a turn counterclockwise to complete the operation. When you harvest your ice cubes the following time, keep an eye on the size of the cubes and make adjustments as needed until you attain the desired ice cube size.
How do I reset my Scotsman ice maker?
Replace the compressor on your Scotsman ice machine. Using the “off” button on the control panel, you may shut off the machine completely. Once you have waited around 10 seconds, hit and hold the “on” button for a couple of seconds. This will switch the machine back on and begin the process of restoring it to its factory settings.
How much water does a Scotsman ice machine use?
F. The necessary inlet water flow rate is 1.25 GPM. All variants are compatible with a standard, 22″ wide Scotsman Ice Storage Bin, such as the BH360, without modification.
Why is my Scotsman ice machine making thin ice?
A number of factors can contribute to the machine producing little quantities of ice or none at all. The following are some of the possibilities. Leaking or an excessive amount of water – Leaks might have an impact on the amount of ice produced by your unit. Examine the hot gas, thermal expansion, and water intake valves to see if there is any leakage.
How does ice thickness sensor work?
When the ice thickness probe is activated, it delivers information to the control board. The ice thickness probe delivers two signals: one for thickness and another for thickness variation. 1. There is no contact between the probe and water. Water must make contact with the ice thickness probe for a continuous period of seven seconds in order for the control board to commence a harvest cycle after the freeze cycle lock-in period of six minutes has lapsed.
How long does a Scotsman ice maker take to make ice?
When the harvest cycle begins, the machine will begin to release the ice after around 20 minutes of operation. Keep an eye out for the first cube harvest: Check the size of the ice cubes before using them. Please keep in mind that the typical size ice cube has a 1/4″ indentation in the wide end.
How do you use a Scotsman ice maker?
Instructions for turning off and turning on a Scotsman ice machine
- By unlocking the door, you may have access to the power buttons.
- Continue to press and hold the red “OFF” button until the machine shuts down and the green status light goes out. Allow all of the ice to gradually melt and drain. There will be no need for you to remove the ice from the trash.
How do you troubleshoot a Scotsman ice maker?
Troubleshooting Guide for the Scotsman Ice Machine
- Troubleshooting Guide for the Scotsman Ice Maker
What does Code 2 mean on Scotsman ice machine?
Diagnostic Codes are a type of code that may be used to diagnose a problem. 2 – A lengthy harvesting period. The system is being shut down. 2 (flashing) – Attempting a second time with a lengthy harvest cycle. 3 – The water is steadily filling.
How do I reset my ice maker?
Turn the ice maker on and off many times. It is as simple as resetting the power to your ice machine to correct the situation. In certain cases, turning the switch off and back on may be enough to restore functioning to your ice maker and get it to start dispenseing again.
How do I clean my Scotsman cm3 ice machine?
Pour 12 ounces of Scotsman Ice Machine Cleaner into the reservoir water and let it sit for 10 minutes. re-position the evaporator lid to its original position. Other components will require cleaning and sanitizing on a regular basis. The entire technique may be found on the machine or in the handbook that came with it.
How does a full ice bin turn off the freezing and harvesting cycles?
When the ice sheet is removed from the evaporator, a water curtain opens, allowing a bin switch to be activated. This brings the harvest cycle to a close and signals the beginning of the following water cycle.
Which type of ice is made with an auger rotating within a flooded evaporator?
Many ice flake machines use an auger that rotates within an insulated freezing cylinder or evaporator to produce the ice flake. Augers are characterized by having cutting edges or flights, which are propelled and geared down to around 8-16 revolutions per minute by a gear motor and gear box combination.