Reset the appliance by pressing the reset button. Taking the plug out of the socket, waiting 30 seconds, and then re-plugging the plug in again
- This E11error indicates that the washer did not fill with water quickly enough, and it took more than 6 minutes for the washer to fill with water to reach full capacity. To resolve the problem, you should just disconnect the washer for 60 seconds to alert it that you have arrived, then plug the washer back in and wait 20 minutes for the problem to resolve itself.
How do you fix an E11 error on an Electrolux washing machine?
What Can I Do to Repair My Washing Machine?
- Water tap inspection
- drain hose inspection
- cleaning of the water valve filter
- cleaning of the pump and its filter Check for clogs in the drains. Check for obstructions in the air tube. Reduce the amount of detergent you use. A Simple Method for Checking the Pressure Sensor.
What does E11 mean on my washing machine?
When the washer takes an excessive amount of time to fill with water, the “E11” error occurs. After a certain length of time, the washer stops filling and will automatically drain if there is not enough water in the washer reservoir.
How do I reset my washing machine after error code?
Resetting the washing machine is simple:
- To switch off the washer, press the POWER button. Unplug the washer from the power outlet or switch off the circuit breaker that serves the appliance. To begin, press and hold the START/PAUSE button for 5 seconds while the power is turned off. Alternatively, re-energize the circuit breaker or plug in the washer again.
How do you put an Electrolux washer in diagnostic mode?
Diagnostic Mode for Electrolux * Press the Cancel button to put the computer into standby mode and make it available for diagnostics. Within 10 seconds of clicking Cancel, push any button on the joystick to bring it back to life. To enter the diagnostic mode, press and hold the button under the display for three seconds at a time.
How do I reset my Electrolux front loader?
Start by turning the machine off at the power outlet, waiting one minute, and then turning it on again. If you still don’t see any improvement, you can attempt a Master Reset. This will completely reset all of the onboard componentry, and it is frequently used effectively by appliance service specialists. Open and close the washing machine door six times in a span of 12 seconds, then repeat the process.
How do I reset my front load washer?
Instead, you can do a power cycle on the device: Unplug it (or turn off the power at the circuit breaker), wait a short period of time for the electrical charge to dissipate from the washer (typically 1 to 5 minutes at the most), and then plug it back into the wall. This is the closest you can come to a “reset” of the washer without breaking the bank.
Is there a reset button on a washing machine?
Most recent washing machines are equipped with a reset option, which allows you to restart the washer if it encounters an error code or other issue while operating. The motor of certain machines may be reset by pressing a button on the machine. When a machine does not have a reset button, disconnecting the washer and then putting it back in is a common method of resetting it.
How do I reset my washing machine?
If you need to reset your washing machine, disconnect it from the electrical outlet. After that, reconnect the washer’s chord to the wall outlet. Finally, open and close the washing machine door six times in order to transmit the reset signal to the system’s various parts and components.
What does error code E11 mean?
In the case of a Hoover washing machine, an E11 error code indicates that there is a problem with the drying sensor. If the drying sensor in your washer dryer is broken or malfunctioning, you will find yourself with a washer dryer that will not dry your garments after they have been laundered.
What is Electrolux smart load sensing?
Utilizing Electrolux’s LuxCareTM wash technology, you can achieve thorough cleaning. It is possible to wash your clothes more effectively because of clever load detection, which determines the optimal quantity of water to use. SmartBoost™ Electrolux’s SmartBoostTM technology helps you get the most out of your detergent by boosting its cleaning power.
Why is my washer stuck on sensing?
When the Kenmore HE Washer gets stopped on the Sensing Cycle and does not move to the Wash cycle, it is most likely due to a problem with one of these three parts: The water inlet valve or inlet valve tap has failed and is in the OFF position. Before starting the wash cycle, the Shift Actuator was unable to shift position. The control board had a malfunction.
What is the problem if the washing machine wont spin?
Normally, your washing machine will not start a spin cycle until it has been completely emptied. It is possible that the drainage line has been blocked with debris from your garments or that it has become kinked. If the hose has become kinked or crushed, it will almost certainly need to be replaced entirely.