Depending on whether or not this control board was affected by a power glitch or surge via the electrical lines, you may be able to reset it by entirely disconnecting the refrigerator for 5 minutes to completely withdraw electrical power from the refrigerator. The board may resume regular operation if the refrigerator is reconnected to the power source.
How do I reset my Kenmore refrigerator control panel?
Simply open one refrigerator door and simultaneously push the “Ultra Ice” button and “Home” button for five seconds to switch off all of the refrigerator’s electronic functions. Disconnect the refrigerator’s power line from the wall outlet it is plugged into. Reconnect the power cord to the wall outlet if it has been disconnected. The refrigerator has been re-programmed.
Does my Kenmore refrigerator have a reset button?
For the controls of the refrigerator to be turned off, open one refrigerator door and push the “Ultra Ice” and “Home” buttons at the same time for five seconds. Disconnect the refrigerator’s power line from the wall outlet it is connected to. Reattach the power cord to the wall socket where it was previously connected. Everything has been reset in the refrigerator.
How do I reset the temperature on my Kenmore refrigerator?
In order to modify the temperature of a Kenmore refrigerator, press the fridge temperature and freezer temperature buttons simultaneously. Hold them for a few seconds or until the display beeps to indicate that they have been released. To discover the 37 degrees Fahrenheit setting, press the fridge temperature button and cycle through the possible settings until you find it.
Why is my Kenmore side by side refrigerator not cooling?
When inspecting the condenser coils, look for signs of dirt or debris—if the condenser coils are unclean, they should be cleaned. This motor pulls air through the condenser coils and over top of the compressor, which is powered by an induction motor. It is impossible for the refrigerator to cool adequately if the condenser fan motor is not operating correctly.
How do you put a Kenmore refrigerator in diagnostic mode?
Activate the diagnostic mode by pushing and holding the Lock button for three seconds, then pressing and holding the Freezer and Refrigerator buttons for five seconds while pressing the Acela Ice button three times. The operational time (the number of minutes it has been plugged in) will be displayed on the digital display.
How do I reset my Kenmore refrigerator after a power outage?
One further method of resetting some Kenmore freezers is to push and hold the up-pointing arrow button until the display eventually begins to show 10 numbers on the display. You will then need to hit the Alarm reset button to complete the process.
How do I reset my refrigerator compressor?
How to Reset the Compressor in Your Refrigerator
- Moving Your Refrigerator Out of the Way
- Step 2: Unplugging Your Refrigerator
- Step 3: Turning Off Your Control Panel
- Step 4: Plugging Your Refrigerator Back In
- Step 5: Resetting the Temperature Settings
- Step 6: Moving Your Refrigerator Back into Place
- Step 7: Waiting at Least 24 Hours
Why is my refrigerator running but not cooling?
Moving Your Refrigerator Out of the Way; Step 2: Unplugging Your Refrigerator; Step 3: Turning Off Your Control Panel; Step 4: Plugging Your Refrigerator Back In; Step 5: Resetting the Temperature Settings; Step 6: Moving Your Refrigerator Back into Place; Step 7: Waiting at Least 24 Hours.
What would cause a refrigerator to stop getting cold?
Vacuum the coils that are located beneath or behind the refrigerator. Poor cooling can be caused by clogged coils. Check to see that nothing is trapped in the condenser fan and that it is free to spin (fans are not included in models with coils on the back of the unit). Connect the refrigerator to the power source and ensure that the fan is functioning while the compressor is operating.
Where is thermostat on Kenmore refrigerator?
When using side-by-side devices, the thermostat is often located on the back of the unit, but when using over-under devices, the thermostat is typically located at the bottom of the refrigerator. Removing the panel that covers the thermostat is the first step. If necessary, a screwdriver will be required to complete this task.
Why is my Kenmore refrigerator not cold enough?
If the refrigerator does not become cold enough, it is possible that something has been stuck in the condenser fan motor blade, or that the condenser fan motor itself is faulty. The condenser fan motor is responsible for drawing air over the condenser coils in order to cool them. The condenser fan motor is positioned below the refrigerator, near the rear of the refrigerator.
What temperature should a Kenmore freezer be set at?
Conserve energy by keeping your freezer’s temperature within a safe range. Kenmore advises keeping the temperature of your freezer compartment between 0 and 2 degrees Fahrenheit, or -16 and -17 degrees Celsius. At this temperature, food may be securely frozen, lowering the likelihood of food thawing and deteriorating during storage. Slightly lower than suggested is preferable than slightly higher than recommended.
Why is my Kenmore fridge not cooling but freezer works?
Make sure to check the evaporator coils to see if they have become frozen over. A malfunctioning evaporator fan will result in insufficient cooling in either the freezer or the refrigerator. To establish if the evaporator fan motor is faulty, crank the fan blade by hand to see if the problem persists. If the fan blade does not revolve freely, the fan motor should be replaced.